Best size inlet LNC2

Submitted by Anonymous on

Forums: 

From: Jim Nordin <panelmaker [at] earthlink.net>
Sender: <marv [at] lancaironline.net>
Subject: Best size inlet LNC2
Date: Tue, 12 Aug 2014 12:22:28 -0400
To: <lml [at] lancaironline.net>

Is there a “best size” inlet in the cowl for the input to the fuel
injector? Non-filtered. This would be the ram air inlet.

3”?

Jim

Best size inlet LNC2

Submitted by Anonymous on

From: Chris Zavatson <chris_zavatson [at] yahoo.com>
Sender: <marv [at] lancaironline.net>
Subject: Re: [LML] Best size inlet LNC2
Date: Tue, 12 Aug 2014 16:46:05 -0400
To: <lml [at] lancaironline.net>
Message Header


Undecoded Message

Jim,

3" works well.

More detail can be found here:

http://www.n91cz.net/InductionSizing/Induction_Inlet_Sizing_rev0.pdf



Chris





--------------------------------------------

On Tue, 8/12/14, Jim Nordin <panelmaker [at] earthlink.net> wrote:



 Subject: [LML] Best size inlet LNC2

 To: "Lancair Mailing List" <lml [at] lancaironline.net>

 Date: Tuesday, August 12, 2014, 9:22 AM

 

 

 

 

  

  

 

 

 

 

 

 

 

 

 

 

 Is there a “best size” inlet

 in the cowl for the input to the fuel

 injector? Non-filtered. This would be the ram air

 inlet.

 

 3”?

 

 Jim

 

 

 

 

 

 

Best size inlet LNC2

Submitted by Anonymous on

From: John Cooper <snopercod [at] comporium.net>
Sender: <marv [at] lancaironline.net>
Subject: Re: [LML] Best size inlet LNC2
Date: Wed, 13 Aug 2014 16:18:44 -0400
To: <lml [at] lancaironline.net>
Message Header


Undecoded Message

On my L-235 with the O-290-D2 engine, I used an analysis similar to
what Chris Z. just posted. I figured out the velocity of the air
going through the carburetor and compared that to the velocity of
the airplane and came up with an expanding ram air inlet that would
slow the air down from 170 KTS to whatever the carb needed (can't
remember). I'll have to measure my intake opening, but I believe it
is ~ 2-3/4" in diameter and expands to 4" in diameter over 11" for a
7° taper on each wall (total included angle of 14 °). The ram air
inlet is connected to the K&N filter and airbox with a short
piece of 4" scat duct. I hope it works (grin).



Note that I made the "cod piece" removable for easy access to check
the lower part of the engine and change the oil.



/files/LML/70554-02-01-R/part1.09030008.08040105 [at] comporium.net" sandbox="" width="282" height="158">


Image


Ram Air Intake.jpg

Post a Reply

More information about text formats

Filtered HTML

  • Web page addresses and e-mail addresses turn into links automatically.
  • Each email address will be obfuscated in a human readable fashion or, if JavaScript is enabled, replaced with a spam resistent clickable link. Email addresses will get the default web form unless specified. If replacement text (a persons name) is required a webform is also required. Separate each part with the "|" pipe symbol. Replace spaces in names with "_".
  • Allowed HTML tags: <a> <em> <strong> <cite> <blockquote> <code> <ul> <ol> <li> <dl> <dt> <dd> <h1> <h2> <h3>
  • Lines and paragraphs break automatically.

Plain text

  • No HTML tags allowed.
  • Each email address will be obfuscated in a human readable fashion or, if JavaScript is enabled, replaced with a spam resistent clickable link. Email addresses will get the default web form unless specified. If replacement text (a persons name) is required a webform is also required. Separate each part with the "|" pipe symbol. Replace spaces in names with "_".
  • Web page addresses and e-mail addresses turn into links automatically.
  • Lines and paragraphs break automatically.
Attachments
Files must be less than 512 MB.
Allowed file types: jpg jpeg gif png txt doc docx xls xlsx pdf ppt pptx pps ppsx odt ods odp mp3 mov mp4 m4a m4v mpeg avi ogg oga ogv weba webp webm.